Видео

Has anyone in this thread come across the diagram for the floor harness that connects to the door with the affected connector? I cut out my connector and need a diagram that shows the colors of the wires coming from the floor harness to the driver's side door harness and how they match up ..99' LX

Great vid man. But I can’t find one with a 4 speed!

I was about to give up until I watched your video. I was down to the snap rings and was frustrated with how difficult it was to get in there. These cars are just too tight. Went to harbor freight and got the right pliers and was able to finish it off. Also just bent the metal tab holding the electrical wires like you did. That screw was not coming out. Thanks for the help.

I have this vehicle. 120k on the clock. One problem so far with an engine cooling fan that goes on strike every 40-50k. No problems otherwise.

When replacing the A/F make sure you buy OAT organic acid technology and the 2022 and up has switched to hoat hybrid organic about tech and don’t mix with regular af cause it turns into a gel and clogs the radiator

My bike has the same exact bottom bracket, and I want to do the same exact conversion, thank you so much for this video, you have helped me a ton.

I sprayed mine w nut buster for a few days ahead of even trying. Then loosened 4 hub bolts and took a nice drive on the bumpiest roads around. Then beat it off w a 5 lb hammer. It eventually came off. I replaced what was left of the backing plate.

dude knows how to twerk , took that guy down the pole

i was waiting for a giggity or something, but was disappoint. professional attitude, cant complain. "get my nuts off"

This is so good! Naming the nuts by MM. Talking to gravity in a positive way. Staying positive no matter what. No cussing. No broken knuckles. lol and a sweet accent. Northern US or Canada? Maine? Minnesota? Uper? Thanks so much man! Very well done!

When you vacume the unit the vacume causes the moisture to boil out of the system

What about the cable clip retainer to the back of the alternator?

I wish you could’ve won a little faster so we could watch seeing how you got it back up in the motor

Hey This ball joint make a problem with a shifting ?

great video! any chance you've replaced the oil pan on the same car? we'd like to see that if possible. thank you!

Cheap build with a good tuner. That's how it's done 😎👍

Great video, I did this repair and also the engine cooler line, helped me watching you as well as the Chiltons. Going to do my transmission cooler lines then put the diff and everything back on. I did not take off my sway bar.

When I first started watching I said: "I cant even tell what I'm looking at.. that things all rusty and crusty n shi* " ...2 minutes later this man gives the same exact description lol (Watching bc i need to adjust the alternator belt on my '96 Odyssey)

The best and most complete video about Mazda 3 compressor clutches.

I am a fellow technician of 7years I'm 29 and I'm going back to the basics on the Honda turbo build. Never knew anything but Mann u just showed me plenty! I was just vibin your whole video 😂 respect

I always learn something new by watching your videos. Would appreciate it if there were more to view. Thanks

YO

Hyena from Lion King I think?

Cool beans sir. My wife has an ‘07 3. I seem to remember a tech next to me doing one of these, I forget the year but, there was no pilot bearing in the crank and no place for one on the transmission shaft. I remember his rat nest comments but overall not a bad job.

Do I need the oil pan support bracket? I know it’s discontinued.

Changing the diode plate and the voltage and coal tegula that same alternator of the video changing the parts I mentioned because it would serve the honda accord next year 98 2002 Just that today they did in a workshop where I went to buy an alternator for my accord 1999 2.3

i change my Subaru 2017 i had to take off the whole spindle

Thanks brother I ended up having to hook up one brake sensor

I’m too dumb to get this to work Jk I just watched your video again and realized I didn’t dead head my pedal thanks man you saved me from another headache and now my clutch engagement is way better

WOW!

You right. Mazda build a lot Stupid

Nice instructional video. A question : It is possible to slide the intake in with the spark plug coils already set ?

You are very funny man! Knowledgeable and skilled mechanic too. Torque specs along with narration...... very entertaining.

You sir are a god send, spent two hours trying to bleed my mazda 3 and wouldn't have thought of this! Thank you!

Dangit, now I'm worried that I've also misdiagnosed the issue. hopefully not. but super helpful video for this portion of it

belt size

belt size????

Is there an update on the blue mustang? After 4 years how did it end up?

As soon as You got to the battery 😂😂 I can relate 😂😂 these engineers man

What is the torque spec for the 13mm nuts

Thank you so much i just did my door on my own you save me a ton

Thank you Sir I’m not a automotive mechanic but you’re video really helped me save $500 by doing it my you made it so easy it’s 95 out today so I appreciate you

Thanks for the help! Do you re-gap the Denso plugs to .06? Don't they come at .04?

Thank You 😊

This guys is either from Khanaaaadaaaahhhhh!!! Or Minny Sodaaaaahhhhhh!!!

To many babies 😂😂😂😅

Thanks. I will let the dealership deal!!!😂

Thanks for your video. The last bolt took me 3 hours to get on. You are right it needs to be bent down towards you a little bit, or it won't in. I fought 14 hours yesterday. It sucks.

Hands down, awesome and brilliant job.

this guy loves ford